NETINTRO(4) BSD Kernel Interfaces Manual NETINTRO(4)
NAME
networking -- introduction to networking facilities
SYNOPSIS
##include <>
##include <>
##include <>
DESCRIPTION
This section is a general introduction to the networking facilities
available in the system. Documentation in this part of section 4 is bro-
ken up into three areas: protocol families (domains), protocols, and
network interfaces.
All network protocols are associated with a specific protocol family. A
protocol family provides basic services to the protocol implementation to
allow it to function within a specific network environment. These ser-
vices may include packet fragmentation and reassembly, routing, address-
ing, and basic transport. A protocol family may support multiple methods
of addressing, though the current protocol implementations do not. A
protocol family is normally comprised of a number of protocols, one per
socket(2) type. It is not required that a protocol family support all
socket types. A protocol family may contain multiple protocols support-
ing the same socket abstraction.
A protocol supports one of the socket abstractions detailed in socket(2).
A specific protocol may be accessed either by creating a socket of the
appropriate type and protocol family, or by requesting the protocol
explicitly when creating a socket. Protocols normally accept only one
type of address format, usually determined by the addressing structure
inherent in the design of the protocol family/network architecture. Cer-
tain semantics of the basic socket abstractions are protocol specific.
All protocols are expected to support the basic model for their particu-
lar socket type, but may, in addition, provide non-standard facilities or
extensions to a mechanism. For example, a protocol supporting the
SOCKSTREAM abstraction may allow more than one byte of out-of-band data
to be transmitted per out-of-band message.
A network interface is similar to a device interface. Network interfaces
comprise the lowest layer of the networking subsystem, interacting with
the actual transport hardware. An interface may support one or more pro-
tocol families and/or address formats. The SYNOPSIS section of each net-
work interface entry gives a sample specification of the related drivers
for use in providing a system description to the config(8) program. The
DIAGNOSTICS section lists messages which may appear on the console and/or
in the system error log, /var/log/messages (see syslogd(8)), due to
errors in device operation.
PROTOCOLS
The system currently supports the Internet protocols, the Xerox Network
Systems(tm) protocols, and some of the ISO OSI protocols. Raw socket
interfaces are provided to the IP protocol layer of the Internet, and to
the IDP protocol of Xerox NS. Consult the appropriate manual pages in
this section for more information regarding the support for each protocol
family.
ADRESING
Associated with each protocol family is an address format. All network
address adhere to a general structure, called a sockaddr, described
below. However, each protocol imposes finer and more specific structure,
generally renaming the variant, which is discussed in the protocol family
manual page alluded to above.
struct sockaddr {
uchar salen;
uchar safamily;
char sadata[14];
};
The field salen contains the total length of the of the structure, which
may exceed 16 bytes. The following address values for safamily are
known to the system (and additional formats are defined for possible
future implementation):
#define AFUNIX 1 /* local to host (pipes) */
#define AFINET 2 /* internetwork: UDP, TCP, etc. */
#define AFNS 6 /* Xerox NS protocols */
#define AFCIT 10 /* CIT protocols, X.25 etc */
#define AFHYLINK 15 /* NSC Hyperchannel */
#define AFISO 18 /* ISO protocols */
ROUTING
Mac OS X provides some packet routing facilities. The kernel maintains a
routing information database, which is used in selecting the appropriate
network interface when transmitting packets.
A user process (or possibly multiple co-operating processes) maintains
this database by sending messages over a special kind of socket. This
supplants fixed size ioctl(2) used in earlier releases.
This facility is described in route(4).
INTERFACES
Each network interface in a system corresponds to a path through which
messages may be sent and received. A network interface usually has a
hardware device associated with it, though certain interfaces such as the
loopback interface, lo(4), do not.
The following ioctl calls may be used to manipulate network interfaces.
The ioctl is made on a socket (typically of type SOCKDGRAM) in the
desired domain. Most of the requests supported in earlier releases take
an ifreq structure as its parameter. This structure has the form
struct ifreq {
#define IFNAMSIZ 16
char ifrname[IFNAMSIZ]; /* if name, e.g. "en0" */
union {
struct sockaddr ifruaddr;
struct sockaddr ifrudstaddr;
struct sockaddr ifrubroadaddr;
short ifruflags;
int ifrumetric;
caddrt ifrudata;
} ifrifru;
#define ifraddr ifrifru.ifruaddr /* address */
#define ifrdstaddr ifrifru.ifrudstaddr /* other end of p-to-p link */
#define ifrbroadaddr ifrifru.ifrubroadaddr /* broadcast address */
#define ifrflags ifrifru.ifruflags /* flags */
#define ifrmetric ifrifru.ifrumetric /* metric */
#define ifrdata ifrifru.ifrudata /* for use by interface */
};
Calls which are now deprecated are:
SIOCSIFADR Set interface address for protocol family. Following the
address assignment, the ``initialization'' routine for
the interface is called.
SIOCSIFDSTADR Set point to point address for protocol family and inter-
face.
SIOCSIFBRDADR Set broadcast address for protocol family and interface.
Ioctl requests to obtain addresses and requests both to set and retrieve
other data are still fully supported and use the ifreq structure:
SIOCGIFADR Get interface address for protocol family.
SIOCGIFDSTADR Get point to point address for protocol family and inter-
face.
SIOCGIFBRDADR Get broadcast address for protocol family and interface.
SIOCSIFLAGS Set interface flags field. If the interface is marked
down, any processes currently routing packets through the
interface are notified; some interfaces may be reset so
that incoming packets are no longer received. When
marked up again, the interface is reinitialized.
SIOCGIFLAGS Get interface flags.
SIOCSIFMETRIC Set interface routing metric. The metric is used only by
user-level routers.
SIOCGIFMETRIC Get interface metric.
There are two requests that make use of a new structure:
SIOCAIFADR An interface may have more than one address associated
with it in some protocols. This request provides a means
to add additional addresses (or modify characteristics of
the primary address if the default address for the
address family is specified). Rather than making sepa-
rate calls to set destination or broadcast addresses, or
network masks (now an integral feature of multiple proto-
cols) a separate structure is used to specify all three
facets simultaneously (see below). One would use a
slightly tailored version of this struct specific to each
family (replacing each sockaddr by one of the family-spe-
cific type). Where the sockaddr itself is larger than
the default size, one needs to modify the ioctl identi-
fier itself to include the total size, as described in
ioctl.
SIOCDIFADR This requests deletes the specified address from the list
associated with an interface. It also uses the
ifaliasreq structure to allow for the possibility of
protocols allowing multiple masks or destination
addresses, and also adopts the convention that specifica-
tion of the default address means to delete the first
address for the interface belonging to the address family
in which the original socket was opened.
SIOCGIFCONF Get interface configuration list. This request takes an
ifconf structure (see below) as a value-result parameter.
The ifclen field should be initially set to the size of
the buffer pointed to by ifcbuf. On return it will con-
tain the length, in bytes, of the configuration list.
/*
* Structure used in SIOCAIFADR request.
*/
struct ifaliasreq {
char ifraname[IFNAMSIZ]; /* if name, e.g. "en0" */
struct sockaddr ifraaddr;
struct sockaddr ifrabroadaddr;
struct sockaddr iframask;
};
/*
* Structure used in SIOCGIFCONF request.
* Used to retrieve interface configuration
* for machine (useful for programs which
* must know all networks accessible).
*/
struct ifconf {
int ifclen; /* size of associated buffer */
union {
caddrt ifcubuf;
struct ifreq *ifcureq;
} ifcifcu;
#define ifcbuf ifcifcu.ifcubuf /* buffer address */
#define ifcreq ifcifcu.ifcureq /* array of structures returned */
};
SEE ALSO
socket(2), ioctl(2), intro(4), config(8), routed(8)
HISTORY
The netintro manual appeared in 4.3BSD-Tahoe.
4.2 Berkeley Distribution November 30, 1993 4.2 Berkeley Distribution
|
