Windows PowerShell command on Get-command Enable-NetAdapterPowerManagement

NAME

Enable-NetAdapterPowerManagement

SYNOPSIS

Enables specific power management features on the network adapter.

SYNTAX

Enable-NetAdapterPowerManagement [-Name] [-ArpOffload] [-AsJob] [-CimSession ]

[-D0PacketCoalescing] [-DeviceSleepOnDisconnect] [-IncludeHidden] [-NoRestart] [-NSOffload] [-PassThru]

[-RsnRekeyOffload] [-SelectiveSuspend] [-ThrottleLimit ] [-WakeOnMagicPacket] [-WakeOnPattern] [-Confirm]

[-WhatIf] []

Enable-NetAdapterPowerManagement [-ArpOffload] [-AsJob] [-CimSession ] [-D0PacketCoalescing]

[-DeviceSleepOnDisconnect] [-IncludeHidden] [-NoRestart] [-NSOffload] [-PassThru] [-RsnRekeyOffload]

[-SelectiveSuspend] [-ThrottleLimit ] [-WakeOnMagicPacket] [-WakeOnPattern] -InterfaceDescription

[-Confirm] [-WhatIf] []

Enable-NetAdapterPowerManagement [-ArpOffload] [-AsJob] [-CimSession ] [-D0PacketCoalescing]

[-DeviceSleepOnDisconnect] [-NoRestart] [-NSOffload] [-PassThru] [-RsnRekeyOffload] [-SelectiveSuspend]

[-ThrottleLimit ] [-WakeOnMagicPacket] [-WakeOnPattern] -InputObject [-Confirm] [-WhatIf]

[]

DESCRIPTION

The Enable-NetAdapterPowerMangement cmdlet enables specific power management features on the network adapter. If

no power options are specified, then all supported power management features are enabled.

PARAMETERS

-ArpOffload []

Indicates that the cmdlet manages the address resolution protocol (ARP) offload capability of the network adapter. The computer, when in low power mode using the ARP offload technology, is able to offload the responsibility of handling responses for incoming ARP protocol requests. Required? false Position? named Default value Accept pipeline input? false Accept wildcard characters? false

-AsJob []

ps_cimcommon_asjob Required? false Position? named Default value Accept pipeline input? false Accept wildcard characters? false

-CimSession

Runs the cmdlet in a remote session or on a remote computer. Enter a computer name or a session object, such

as the output of a New-CimSession or Get-CimSession cmdlet. The default is the current session on the local

computer. Required? false Position? named Default value Accept pipeline input? false Accept wildcard characters? false

-D0PacketCoalescing []

Indicates that the cmdlet manages the D0 packet coalescing capability of the network adapter. This feature enables power saving on the computer by reducing the number of receive interrupts. This reduces the number of receive interrupts by coalescing random broadcast or multicast packets. The processing overhead and power consumption is significantly reduced on the computer. Required? false Position? named Default value Accept pipeline input? false Accept wildcard characters? false

-DeviceSleepOnDisconnect []

Indicates that the cmdlet manages the device sleep on disconnect capability of the network adapter.

This feature allows the device to stand-by in a low power mode when media is disconnected and wake when media

is connected again. Required? false Position? named Default value Accept pipeline input? false Accept wildcard characters? false

-IncludeHidden []

Indicates that the cmdlet includes both visible and hidden network adapters in the operation. By default only visible network adapters are included. If a wildcard character is used in identifying a network adapter and this parameter has been specified, then the wildcard string is matched against both hidden and visible network adapters. Required? false Position? named Default value Accept pipeline input? false Accept wildcard characters? false

-InputObject

Specifies the input to this cmdlet. You can use this parameter, or you can pipe the input to this cmdlet. Required? true Position? named Default value Accept pipeline input? true (ByValue) Accept wildcard characters? false

-InterfaceDescription

Specifies an array of network adapter interface descriptions. For a physical network adapter this is typically the name of the vendor of the network adapter followed by a part number and description, such as Contoso 12345 Gigabit Network Device. Required? true Position? named Default value

Accept pipeline input? true (ByPropertyName)

Accept wildcard characters? true

-Name

Specifies an array of network adapter names. Required? true Position? 1 Default value

Accept pipeline input? true (ByPropertyName)

Accept wildcard characters? true

-NoRestart []

Indicates that the cmdlet does not restart the network adapter after completing the operation. Many advanced properties require restarting the network adapter before the new settings take effect. Required? false Position? named Default value Accept pipeline input? false Accept wildcard characters? false

-NSOffload []

Indicates that the cmdlet manages the neighbor solicitation (NS) offload capability of the network adapter. The computer, when in low power mode using the NS offload technology, is able to offload the handling of responses for incoming NS protocol requests. Required? false Position? named Default value Accept pipeline input? false Accept wildcard characters? false

-PassThru []

Returns an object representing the item with which you are working. By default, this cmdlet does not generate any output. Required? false Position? named Default value Accept pipeline input? false Accept wildcard characters? false

-RsnRekeyOffload []

Indicates that the cmdlet manages the Wi-Fi robust security network (RSN) rekey offload capability of the

network adapter. The computer, when it goes into sleep state, is able to offload the group temporal key (GTK) rekeying for wake on wireless LAN (WoWLAN). Required? false Position? named Default value Accept pipeline input? false Accept wildcard characters? false

-SelectiveSuspend []

Indicates that the cmdlet manages the selective suspend capability of the network adapter. The network drive interface specification (NDIS) selective suspend interface allows NDIS to suspend an idle

network adapter by transitioning the adapter to a low-power state. This enables the computer to reduce the

power overhead on the processor and network adapter. Required? false Position? named Default value Accept pipeline input? false Accept wildcard characters? false

-ThrottleLimit

Specifies the maximum number of concurrent operations that can be established to run the cmdlet. If this parameter is omitted or a value of 0 is entered, then Windows PowerShellr calculates an optimum throttle limit for the cmdlet based on the number of CIM cmdlets that are running on the computer. The throttle limit applies only to the current cmdlet, not to the session or to the computer. Required? false Position? named Default value Accept pipeline input? false Accept wildcard characters? false

-WakeOnMagicPacket []

Indicates that the cmdlet manages the wake on magic packet capability of the network adapter. The magic packet is a broadcast frame containing anywhere within its payload 6 bytes of all 255 (FF FF FF FF

FF FF in hexadecimal), followed by sixteen repetitions of the 48-bit MAC address of the target computer, for a

total of 102 bytes. Required? false Position? named Default value Accept pipeline input? false Accept wildcard characters? false

-WakeOnPattern []

Indicates that the cmdlet manages the wake on pattern capability of the network adapter. A wake pattern refers to network packet filters that determine if incoming network traffic should wake the computer. These patterns can be enabled on the network adapter. The following wake patterns may be supported by a network adapter:

-- Wake Pattern.

-- Wake on new incoming TCP connection for IPv4 and IPv6 including TCP SYN IPv4 and TCP SYN IPv6.

-- 802.1x re-authentication packets.

-- Bitmapped Patterns: Most network adapters can be programmed with bit-mapped pattern filters. Bitmapped

patterns are defined by a bit-map mask and a pattern filter. As a network packet is received, it is masked

using the bitmap mask and then compared to the pattern filter. If there is a match, then the network adapter wakes the computer. Required? false Position? named Default value Accept pipeline input? false Accept wildcard characters? false

-Confirm []

Prompts you for confirmation before running the cmdlet.Prompts you for confirmation before running the cmdlet. Required? false Position? named Default value false Accept pipeline input? false Accept wildcard characters? false

-WhatIf []

Shows what would happen if the cmdlet runs. The cmdlet is not run.Shows what would happen if the cmdlet runs. The cmdlet is not run. Required? false Position? named Default value false Accept pipeline input? false Accept wildcard characters? false This cmdlet supports the common parameters: Verbose, Debug, ErrorAction, ErrorVariable, WarningAction, WarningVariable, OutBuffer, PipelineVariable, and OutVariable. For more information, see about_CommonParameters (https:/go.microsoft.com/fwlink/?LinkID=113216).

INPUTS

Microsoft.Management.Infrastructure.CimInstance#ROOT/StandardCimv2/MSFT_NetAdapterPowerManagementSettingData[] The Microsoft.Management.Infrastructure.CimInstance object is a wrapper class that displays Windows Management Instrumentation (WMI) objects. The path after the pound sign (#) provides the namespace and class name for the underlying WMI object.

OUTPUTS

Microsoft.Management.Infrastructure.CimInstance#ROOT/StandardCimv2/MSFT_NetAdapterPowerManagementSettingData The Microsoft.Management.Infrastructure.CimInstance object is a wrapper class that displays Windows Management Instrumentation (WMI) objects. The path after the pound sign (#) provides the namespace and class name for the underlying WMI object.

Example 1: Enable power management on the specified network adapter

PS C:\>Enable-NetAdapterPowerManagement -Name "Ethernet 1"

This command enables power management on the network adapter named Ethernet 1 and restarts the network adapter.

Example 2: Enable power management on the specified network adapter

The first command gets the network adapter named Ethernet 2 and stores the result in the variable named

$NetAdapter2. The second command and enables power management for the network adapter stored in the $NetAdapter

variable.

PS C:\> $NetAdapter2 = Get-NetAdapter -Name "Ethernet 2"

PS C:\> Enable-NetAdapterPowerMangement -InputObject $NetAdapter2

This command is a version of the cmdlet that uses the pipeline to select the network adapter named Ethernet 3 and pipes that object into this cmdlet.