Windows PowerShell command on Get-command New-NetIPAddress

NAME

New-NetIPAddress

SYNOPSIS

Creates and configures an IP address.

SYNTAX

New-NetIPAddress [-IPAddress] [-AddressFamily {IPv4 | IPv6}] [-CimSession ]

[-DefaultGateway ] [-PolicyStore ] [-PreferredLifetime ] [-PrefixLength ]

[-SkipAsSource ] [-ThrottleLimit ] [-Type {Unicast | Anycast}] [-ValidLifetime ]

-InterfaceAlias [-Confirm] [-WhatIf] []

New-NetIPAddress [-IPAddress] [-AddressFamily {IPv4 | IPv6}] [-CimSession ]

[-DefaultGateway ] [-PolicyStore ] [-PreferredLifetime ] [-PrefixLength ]

[-SkipAsSource ] [-ThrottleLimit ] [-Type {Unicast | Anycast}] [-ValidLifetime ]

-InterfaceIndex [-Confirm] [-WhatIf] []

DESCRIPTION

The New-NetIPAddress cmdlet creates and configures an IP address. To create a specific IP address object, specify

either an IPv4 address or an IPv6 address, and an interface index or interface alias. We recommend that you define the prefix length, also known as a subnet mask, and a default gateway. If you run this cmdlet to add an IP address to an interface on which DHCP is already enabled, then DHCP is automatically disabled. If Duplicate Address Detection (DAD) is enabled on the interface, the new IP address is not usable until DAD successfully finishes, which confirms the uniqueness of the IP address on the link.

PARAMETERS

-AddressFamily []

Specifies an IP address family. The cmdlet creates an IP address for the family. If you do not specify this parameter, the property is automatically generated. The acceptable values for this parameter are:

-- IPv4

-- IPv6

Required? false Position? named Default value none Accept pipeline input? false Accept wildcard characters? false

-CimSession []

Runs the cmdlet in a remote session or on a remote computer. Enter a computer name or a session object, such

as the output of a New-CimSession or Get-CimSession cmdlet. The default is the current session on the local

computer. Required? false Position? named Default value none Accept pipeline input? false Accept wildcard characters? false

-DefaultGateway []

Specifies the IPv4 address or IPv6 address of the default gateway for the host. Default gateways provide a default route for TCP/IP hosts to use when communicating with other hosts on remote networks. Required? false Position? named Default value none Accept pipeline input? false Accept wildcard characters? false

-InterfaceAlias

Specifies an alias of a network interface. The cmdlet creates an IP address for the alias. Required? true Position? named Default value none

Accept pipeline input? True (ByPropertyName)

Accept wildcard characters? false

-InterfaceIndex

Specifies an index of a network interface. The cmdlet creates an IP address for the index. Required? true Position? named Default value none

Accept pipeline input? True (ByPropertyName)

Accept wildcard characters? false

-IPAddress

Specifies the IPv4 or IPv6 address to create. Required? true Position? 1 Default value none

Accept pipeline input? True (ByPropertyName)

Accept wildcard characters? false

-PolicyStore []

Specifies a PolicyStore value. The acceptable values for this parameter are:

-- ActiveStore. The IP address information is valid.

-- PersistentStore. The computer saves IP address information across restarts. When the computer restarts, it

copies the saved settings to the ActiveStore. The default value is ActiveStore. Specify ActiveStore only. If you do not specify this parameter, the default entries are created in both the ActiveStore and the PersistentStore. Required? false Position? named Default value none Accept pipeline input? false Accept wildcard characters? false

-PreferredLifetime []

Specifies a preferred lifetime, as a TimeSpan object, for an IP address. To obtain a TimeSpan object, use the

New-TimeSpan cmdlet.

Required? false Position? named Default value none Accept pipeline input? false Accept wildcard characters? false

-PrefixLength []

Specifies a prefix length. This parameter defines the local subnet size, and is also known as a subnet mask. Required? false Position? named Default value none Accept pipeline input? false Accept wildcard characters? false

-SkipAsSource []

Indicates whether an address is a primary IP address. This parameter identifies the primary IP address for outgoing traffic in a multiple IP address scenario. If this parameter is set to True, the addresses are not used for outgoing traffic and are not registered in DNS. Required? false Position? named Default value none Accept pipeline input? false Accept wildcard characters? false

-ThrottleLimit []

Specifies the maximum number of concurrent operations that can be established to run the cmdlet. If this parameter is omitted or a value of 0 is entered, then Windows PowerShellr calculates an optimum throttle limit for the cmdlet based on the number of CIM cmdlets that are running on the computer. The throttle limit applies only to the current cmdlet, not to the session or to the computer. Required? false Position? named Default value none Accept pipeline input? false Accept wildcard characters? false

-Type []

Specifies an IP address type. The acceptable values for this parameter are:

-- Unicast

-- Anycast

The default value is Unicast. Required? false Position? named Default value none Accept pipeline input? false Accept wildcard characters? false

-ValidLifetime []

Specifies a valid lifetime value, as a TimeSpan object, for an IP address. To obtain a TimeSpan object, use

the New-TimeSpan cmdlet.

Required? false Position? named Default value none Accept pipeline input? false Accept wildcard characters? false

-Confirm []

Prompts you for confirmation before running the cmdlet.Prompts you for confirmation before running the cmdlet. Required? false Position? named Default value false Accept pipeline input? false Accept wildcard characters? false

-WhatIf []

Shows what would happen if the cmdlet runs. The cmdlet is not run.Shows what would happen if the cmdlet runs. The cmdlet is not run. Required? false Position? named Default value false Accept pipeline input? false Accept wildcard characters? false This cmdlet supports the common parameters: Verbose, Debug, ErrorAction, ErrorVariable, WarningAction, WarningVariable, OutBuffer, PipelineVariable, and OutVariable. For more information, see about_CommonParameters (https:/go.microsoft.com/fwlink/?LinkID=113216).

INPUTS

None

OUTPUTS

Microsoft.Management.Infrastructure.CimInstance#root\StandardCimv2\MSFT_NetIPAddress The Microsoft.Management.Infrastructure.CimInstance object is a wrapper class that displays Windows Management Instrumentation (WMI) objects. The path after the pound sign (#) provides the namespace and class name for the underlying WMI object.

Example 1: Add an IPv4 address

PS C:\>New-NetIPAddress -InterfaceIndex 12 -IPAddress 192.168.0.1 -PrefixLength 24 -DefaultGateway 192.168.0.5

The second command removes the IPv4 address. To remove the IPv4 address, use the Remove-NetIPAddress cmdlet.

PS C:\>Remove-NetIPAddress -IPAddress 192.168.0.1 -DefaultGateway 192.168.0.5

The first command adds a new IPv4 address to the network interface at index 12. The PrefixLength parameter specifies the subnet mask for the IP address. In this example, the PrefixLength of 24 equals a subnet mask of 255.255.255.0. When you add an IPv4 address, the address specified for the Default Gateway must be in the same subnet as the IPv4 address that you add.